中文字幕在线观看国产完整,在线看亚洲国产精品一区二区

蘇州工業園區翔宇電子有限公司

化學用品一站式服務????

化工生產銷售?????

熱點詞推薦：

產品展示?/Product

ABOUT MOUMOU?

網站首頁 >> 瞬干膠

產品展示

DEDT 8416瞬干膠

瞬干膠

市場價:0.00

價格:0.00

PRODUCT DESCRIPTIONDEDT 8416 a low viscosity surface insensitive cyanoacrylateadhesive. Product 8416 is specifically formulated to rapidlybond difficult substrates and to perform in lower humiditysituations. (Mil-A-46050C Type II, Class I).TYPICAL PROPERTIESEster Base ethyl-2-cyanoacrylateAppearance Clear, colourlessFlashpoint >80°CDensity 1,05Shelf Life 12 months, unopenedViscosity (Brookfield) @ 25°C 1300-1500cP(Spindle 1, 20rpm)POLYMER PROPERTIESAppearance Clear, colourlessSoftening Point c. 125°CRefractive Index, nD20 1,45Full Cure Time 24 hoursSolubility DMF, acetonitrile, acetoneCURED SPEED VS. SUBSTRATEBalsa / Balsa <5 secondsRubber / Rubber <5 secondsNitrile / Nitrile <5 secondsNeoprene / Neoprene <5 secondsEPDM / EPDM <5 secondsSteel / Steel 10-20 secondsPVC / PVC 3-10 secondsPolycarbonate / Polycarbonate 10-40 secondsCURED SPEED VS. GAPThe rate of cure will depend on the bondline gap. Thinbondlines result in high cure speeds, increasing the bond gapwill decrease the rate of cure.CURED SPEED VS. ACTIVATORWhere cure speed is unacceptably long due to large gaps,applying activator to the surface will improve cure speed,However, this can reduce ultimate strength of the bond andtherefore testing is recommended to confirm effect.SHEAR STRENGTHGrit Blasted Steel >15 N/mm2Etched Aluminium >11 N/mm2Nitrile Rubber >10 N/mm2Polycarbonate >12 N/mm2ABS 6~18N/mm2PVC 6~18N/mm2DIRECTIONS FOR USEFor best results the surface must be clean and free fromoil ,grease, rust and other contamination. Best results withDEDT adhesive are obtained by using the minimum amount ofadhesive needed to fill the gap between the two matingsurfaces. Apply firm pressure to mated surfaces until adhesivesets.BLOOMING/CHLOROSISVapor generated by uncured liquid adhesive can be depositedon nearby surfaces leaving a white residue. The condition canbe reduced using one or more of the following methods:Clean with DEDT 755.Reduce quantity of the adhesive used.Increase the airflow.Speed the fixture/cure of the adhesive by using an accelerator.PRODUCT STORAGEStore product in the unopened container in a dry location.Optimal storage:2℃ to 8℃. Keep container tightly capped. Ifstored at low temperature, product must be allowed to returnto room temperature before use, This normally takes 8 to12hours.DISCLAIMERThe data contained within this Technical Data Sheet arefurnished for information only and are believed to be reliableat the time of issue. We cannot assume responsibility forresults obtained by others over whose methods we have nocontrol. It is the responsibility of the customer to determinethe products suitability for use. DEDT Limited and itsassociated companies accept no liability arising out of the useof this information or the products described herein.
DEDT 835瞬干膠

瞬干膠

市場價:0.00

價格:0.00

PRODUCT DESCRIPTIONDEDT 835 a high viscosity low-odour, low-bloom cyanoacrylate adhesive. The product has a rapid cure rate and issuitable for porous substrates or where gap fill may be required.TYPICAL PROPERTIESEster Base Alkoxy-ethyl cyanoacrylateAppearance Clear, colourlessFlashpoint >81°CDensity 1.10Shelf Life 12 months, unopenedViscosity (Brookfield) @ 25°C 850-1250cPs(Spindle 1, 20rpm)POLYMER PROPERTIESAppearance Clear, colourlessSoftening Point c. 100°CRefractive Index, nD20 1,45Full Cure Time 24 hoursSolubility DMF, acetonitrile, acetoneCURED SPEED VS. SUBSTRATEBalsa / Balsa 15- 20 secondsRubber / Rubber <7 secondsNitrile / Nitrile <7 secondsNeoprene / Neoprene <7 secondsEPDM / EPDM <7 secondsSteel / Steel 20-40 secondsPVC / PVC 20-40 secondsPolycarbonate / Polycarbonate 20-50 secondsCURED SPEED VS. GAPThe rate of cure will depend on the bondline gap. Thin bondlines result in high cure speeds, increasing the bond gapwill decrease the rate of cure.CURED SPEED VS. ACTIVATORWhere cure speed is unacceptably long due to large gaps, applying activator to the surface will improve cure speed,However, this can reduce ultimate strength of the bond and therefore testing is recommended to confirm effect.SHEAR STRENGTHGrit Blasted Steel >14 N/mm2Etched Aluminium >10 N/mm2Nitrile Rubber >4 N/mm2Polycarbonate >3 N/mm2Technical Data Sheet835ABS >6N/mm2PVC >2N/mm2DIRECTIONS FOR USEFor best results the surface must be clean and free from oil ,grease, rust and other contamination. Best results withDEDT adhesive are obtained by using the minimum amount of adhesive needed to fill the gap between the twomating surfaces. Apply firm pressure to mated surfaces until adhesive sets.PRODUCT STORAGEStore product in the unopened container in a dry location. Optimal storage:2℃ to 8℃. Keep container tightly capped.If stored at low temperature, product must be allowed to return to room temperature before use, This normally takes 8to12 hours.DISCLAIMERThe data contained within this Technical Data Sheet are furnished for information only and are believed to be reliableat the time of issue. We cannot assume responsibility for results obtained by others over whose methods we have nocontrol. It is the responsibility of the customer to determine the products suitability for use. DEDT Limited and itsassociated companies accept no liability arising out of the use of this information or the products described herein.

共 2 條記錄1

推薦產品

DEDT 8416瞬干膠
DEDT 835瞬干膠
DEDT 1770處理劑
DEDT AC9促進劑
DEDT 1050AB膠

蘇州工業園區翔宇電子有限公司

地址：蘇州工業園區科成路2號1幢3樓

電話：0512-67065375

郵件：xy.liu@dedt.com.cn

手機：13815267065